Subaru Legacy

since 1990-1998 release

Repair and operation of the car



Subaru Legacy
+ 1.1. Identification numbers
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
   5.1. Introduction
   5.2. Technical characteristics
   5.3. Removal of pressure in fuel system
   5.4. Check of the fuel pump
   5.5. Fuel pump
   5.6. Fuel separator (only models 4WD)
   5.7. Fuel level sensor
   5.8. Fuel tank
   5.9. Casing of the air filter
   5.10. Accelerator cable
   5.11. Electronic system of injection of fuel
   5.12. Fuel system
   5.13. System of air supply
   5.14. System of electronic control
   5.15. Check of system of injection of fuel
   + 5.16. Check and replacement of elements of system of injection of fuel
   5.17. Turbocharger
   5.18. Check of the executive mechanism of the gate of a turbocharger
   5.19. General check of a turbocharger
   5.20. Removal and installation of a turbocharger
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
+ 14. Electric equipment


2d841be8


5.8. Fuel tank

GENERAL INFORMATION

The fuel tank and separator of fuel on models 4WD

1 – canister
2 – hose
3 – hose
4 – hose
5 – hose
6 – the giving hose
7 – fuel filter
8 – the giving hose
9 – fuel-supply line
10 – returnable fuel-supply line
11 – giving топливопровд
12 – air hose
13 – air tube
14 – protective arm
15 – cover of a fuel-filling mouth
16 – sealing rings
17 – laying
18 – fuel-filling pipe
19 – arm
20 – separator
21 – arm
22 – a hose In
23 – a hose With
24 – hose And
25 – arm
26 – separator
27 – arm
28 – casing
29 – a hose With
30 – hose And
31 – a hose In
32 – auxiliary adjusting valve of cleaning

The fuel tank of models 4WD (on models 2WD the fuel tank is similar)

1 – block of the fuel pump
2 – fuel level sensor
3 – fuel pump
4 – fuel filter
5 – laying
6 – hose
7 – air hose
8 – tank
9 – fixing tapes
10 – protection
11 – arm
12 – casing
13 – backpressure valve,
14 – hose,
15 – the giving hose
16 – returnable hose
17 – returnable pipe
18 – the giving pipe
19 – pipe
20 – pipe
21 – the additional giving hose
22 – returnable hose
23 – the giving hose
24 – the additional giving hose
25 – hose
26 – ventilation hose
27 – ventilation hose
28 – pipe
29 – air pipe
30 – air pipe
31 – laying
32 – filter

Fastening of a toplivonalivny pipe and pipe of ventilation to the fuel tank

1 – топливнозаливныя pipe

2 – ventilation pipe

At removal of the fuel tank fuel level in it has to be minimum.

Removal

PERFORMANCE ORDER
1. Uncover a fuel-filling mouth to level pressure in a tank with atmospheric.
2. Remove a weight wire from the accumulator.
3. Lift the car and record on supports.
4. Remove a back exhaust pipe and the muffler.
5. On models 4WD remove back differential.
6. On models 4WD remove a back beam.
7. Disconnect a fuel-filling pipe from the fuel tank (see rice. Fastening of a toplivonalivny pipe and pipe of ventilation to the fuel tank).
8. Support the fuel tank by a jack, having laid a board between a jack and the fuel tank.
9. Remove protection of the fuel tank, then unscrew screws, the fixing two tapes of fastening of the fuel tank.
10. Lower a jack and take the fuel tank from under the car.
11. Installation is made in the sequence, the return to removal.