Subaru Legacy

since 1990-1998 release

Repair and operation of the car

Subaru Legacy
+ 1.1. Identification numbers
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
- 8. Transmissions
   + 8.1. Mechanical transmission
   - 8.2. Automatic transmission
      8.2.1. Introduction
      8.2.2. Technical characteristics
      8.2.3. Diagnostics of leak of operational liquids
      8.2.4. Lever and cable of gear shifting
      8.2.5. Cable of the choice of transfers
      8.2.6. Switch of blocking of a starter and light of a backing
      8.2.7. Replacement of sealing rings
      8.2.8. Check and replacement of support of the transmission
      8.2.9. Adjustment of a brake tape
      8.2.10. Removal and installation of the transmission
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
+ 14. Electric equipment

8.2.4. Lever and cable of gear shifting

GENERAL INFORMATION

The lever of gear shifting of cars from 1990 to 1994

1 – cover
2 – switch button
3 – handle button
4 – spring
5 – handle
6 – the indicator of the included transfer
7 – switch of a starting position
8 – control lamp
9 – unblocking button
10 – gear shifting lever basis
11 – solenoid
12 – laying
13 – cover of a cable of the choice of transfers

14 – nut
15 – cable of the choice of transfers
16 – nut
17 – draft,
18 – lock plate
19 – gear shifting lever
20 – washer
21 – laying
22 – laying
23 – cover
24 – pin
25 – pin

The lever of gear shifting of models since 1995

1 – button
2 – spring
3 – handle
4 – the indicator of the included transfer
5 – switch of a starting position
6 – control lamp
7 – shift lock solenoid
8 – gear shifting lever basis
9 – laying
10 – cable cover
11 – nut
12 – nut

13 – cable
14 – bracket
15 – draft
16 – gear shifting lever
17 – lock plate
18 – spring
19 – pin
20 – laying
21 – washer
22 – cover
23 – laying
24 – pin

Removal

PERFORMANCE ORDER

1. Establish the gear shifting lever in neutral situation.
2. Lift the car and record on supports.
3. Remove a reception exhaust pipe.
	4. Disconnect a cable of the choice of transfers from the lever on the transmission (bolts of fastening of a cover of a cable are specified by shooters).
5. Unscrew the grounding tire from a transmission case.
	6. Disconnect a cable of the choice of transfers from the gear shifting lever. For a detachment of a cable of the choice of transfers from the lever of gear shifting unscrew a nut on the end of a cable (the left arrow) then unscrew a nut of fastening of a cover of a cable (the right arrow) and take a cable from a groove.
7. Unscrew a nut of fastening of a cover of a cable of the choice of transfers and take a cable through a groove in an arm.
8. Remove the central console.
	9. Unscrew two screws of fastening of the handle of the lever of gear shifting and, having pulled the handle up, remove it from the gear shifting lever.
	10. Disconnect electric sockets from the solenoid of the lock of shift and the switch of a starting position.
	11. Unscrew 4 screws (are specified by shooters) fastenings of the indicator of provision of the included transfer.
	12. Raise the indicator and disconnect the electric socket of glow lamps.
	13. Unscrew screws of fastening of the basis of the lever of gear shifting (are specified by shooters) and take assembly of the lever of gear shifting from the car.
14. Installation is made in the sequence, the return to removal. Adjust a cable of the choice of transfers.