Subaru Legacy

since 1990-1998 release

Repair and operation of the car



Subaru Legacy
+ 1.1. Identification numbers
+ 2. Maintenance
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine installed in the car
   3.3. Top dead point of the first cylinder
   3.4. Cover of a head of the block of cylinders
   3.5. Inlet collector
   + 3.6. Gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a bent shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. Oil pallet
   3.12. Oil pump
   3.13. Drive flywheel / plate
   3.14. Replacement of a back sealing ring of a bent shaft
   3.15. Suspension bracket of the power unit
   - 3.16. Capital repairs of the engine
      3.16.1. Technical characteristics
      3.16.2. Check of a compression
      3.16.3. Check of the engine by means of the vacuum gage
      3.16.4. Recommendations about removal of the engine
      3.16.5. Removal of the engine
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Cleaning and survey of a head of the block of cylinders
      3.16.9. Assembly of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a bent shaft with rods
      3.16.13. Block of cylinders of the engine
      3.16.14. Honingovaniye of cylinders
      3.16.15. Rods
      3.16.16. Bent shaft
      3.16.17. Survey of radical and conrod bearings
      3.16.18. Engine balance of assembly at capital repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working gaps of conrod bearings
      3.16.21. Check of working gaps of radical bearings of a bent shaft
      3.16.22. Assembly of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Installation of the engine
      3.16.26. Start of the engine after capital repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
+ 14. Electric equipment


2d841be8


3.16.10. Removal of pistons

GENERAL INFORMATION

Elements of fastening of piston fingers

1 – stopper
2 – lock ring
3 – piston finger
4 – flange
5 – short and long bolts of fastening of the left block of cylinders
6 – long bolts of fastening of the right block of cylinders

Prevention

If there is a deposit in the top part of the cylinder, remove it with a scraper from soft material or special adaptation


PERFORMANCE ORDER
1. For a provorachivaniye of a bent shaft of the engine temporarily screw in a bolt of fastening of a pulley of a bent shaft.
2. Unscrew traffic jams from four technological openings for access to lock rings of a piston finger.
3. For removal of a lock ring of a piston finger from the piston, install the piston in the lower dead point and, using flat-nose pliers, remove lock rings.
4. Using the special tool (or the hammer and the special tool), take piston fingers through technological openings.
5. If necessary take the piston from the block of cylinders.