Subaru Legacy

since 1990-1998 release

Repair and operation of the car



Subaru Legacy
+ 1.1. Identification numbers
+ 2. Maintenance
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine installed in the car
   3.3. Top dead point of the first cylinder
   3.4. Cover of a head of the block of cylinders
   3.5. Inlet collector
   + 3.6. Gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a bent shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. Oil pallet
   3.12. Oil pump
   3.13. Drive flywheel / plate
   3.14. Replacement of a back sealing ring of a bent shaft
   3.15. Suspension bracket of the power unit
   - 3.16. Capital repairs of the engine
      3.16.1. Technical characteristics
      3.16.2. Check of a compression
      3.16.3. Check of the engine by means of the vacuum gage
      3.16.4. Recommendations about removal of the engine
      3.16.5. Removal of the engine
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Cleaning and survey of a head of the block of cylinders
      3.16.9. Assembly of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a bent shaft with rods
      3.16.13. Block of cylinders of the engine
      3.16.14. Honingovaniye of cylinders
      3.16.15. Rods
      3.16.16. Bent shaft
      3.16.17. Survey of radical and conrod bearings
      3.16.18. Engine balance of assembly at capital repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working gaps of conrod bearings
      3.16.21. Check of working gaps of radical bearings of a bent shaft
      3.16.22. Assembly of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Installation of the engine
      3.16.26. Start of the engine after capital repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
+ 14. Electric equipment


2d841be8


3.16.16. Bent shaft

Check

PERFORMANCE ORDER
1. Clear a bent shaft, using the corresponding solvent, and drain it compressed air.
2. Check radical and conrod necks of a bent shaft for wear, corrosion and cracks.
3. Wear of a conrod neck is characterized by metal knocks during the operation of the engine, especially under loading on small turns, and reduction of pressure of oil.
4. Wear of radical necks of a bent shaft is characterized by strong vibration of the engine and the metal knock increasing at increase in turns of the engine and also reduction of pressure of oil.
5. Check necks of a bent shaft for a roughness. Any noticeable roughness specifies that the bent shaft needs to be pereshlifovat or replaced.
6. If the bent shaft was перешлифован, check agnails around openings for lubricant. In the presence of agnails remove them with a small file or a shaber.
7. Carefully clear openings and channels of shaving.
8. Using a micrometer, measure diameter of radical and conrod necks of a bent shaft and compare results with technical requirements. You perform measurement of necks in several points both on diameter, and on neck length that will allow to reveal ovality and conicity if it is present.
9. Check the surfaces of contact of oil consolidation on each end of a bent shaft for wear and other damages. If wear of a neck of a bent shaft too big, then, perhaps, is required replacement of a bent shaft.